TEL: +86-0510-86573908-814
E-MAIL: mck@dlclx.cn
Categories
Contact Us
Jiangyin Deling Gearbox Co.,Ltd
Add:No.19 Yingbin Road Qiaoqi Industrial Park Jiangyin City, Jiangsu, China
Tel:+86-0510-86573908-814
Mob:+8613915307777
E-mail:mck@dlclx.cn
Gearbox Rotary Reducer

Gearbox Rotary Reducer

Gearbox Rotary reducer Made in China of Gearbox Rotary reducer Details: Model description 1.The three stage planetary size is 60, the A type is installed with the eccentricity of 2.5, and the transmission ratio is 140. If you have special requirements, please explain when you order. 2. Structure...
Chat Now

Gearbox Rotary reducer Made in China

In order to accurately adjust the clearance between the output shaft gear and the gear ring, the eccentricity adjustment between the output gear shaft and the fixed flange can be adjusted when the output shaft is assembled. 

The output gear shaft adopts the spline shaft insert structure or the integral forging structure, and the gear tooth surface hardness HRC57 - 62 (also can be surface hardening on the tooth surface according to the customer's request hardness).

The gear displacement coefficient +0.5 is used to repair the top of the tooth.

image001_副本.jpg

Performance parameters and dimensions   

image002_副本.jpg


1) Each minimum value is for reference only in the design range. For specific selection, it is necessary to specify the size.

2) Output pinion gear number, modulus, given at the time of ordering.

3) The flange bolts are graded 10.9.

4) The dimensions D1, D2 are determined by the pinion structure, and the smaller dimensions need to be explained first.

5) For special installation, higher torque and non-standard speed performance requirements, please contact us.

Another: For the following two types of installation requirements, please request the installation size as an order drawing


  image004.jpg

 

Nominal transmission ratio


   image006.jpg


Reducer selection

T 2 (N.m): Output pinion load torque

T 2k—Modified load torque

K - Coefficients corresponding to the utilization level and load status of the table organization

The rated torque of the gearbox selected must satisfy the following formula:

T 2k=T 2×K<Tnom (see parameter table)


Installation instructions

In order to ensure the normal operation of the slewing mechanism, the mounting center hole of the steel structure must be concentric, and the flange mounting surface must be perpendicular to it. The relative position between the mounting hole of the steel structure and the mounting surface of the flange is not allowed to change excessively under the influence of environmental influences and external forces. The recommended tolerances are as follows.


  image008.jpg

   image010.jpg

 

A:  When the workpiece rotates around the reference centerline, the amount of axial runout in any measurement plane must not exceed the value

B:  The centerline of each machining axis hole must be located in a cylinder whose deviation from the centerline of the reference plane is this value.

 

Oil selection and replacement

The correct choice of oil and reasonable maintenance can extend the service life of the reducer.

(1) Lubricants:

New reducer or replacement repaired reducer. Use oil for the first time after 200 hours. Replace oil every 1000 hours. Change oil at least once a year.

(2) Grease:

Add it once a week or 50 hours after work

(3) Recommended Lubricant:


   image012.jpg


Packaging

All exported gearboxes covered with Anti rust oil and plastic film, then packed in wood box with Fumigation.


image016_副本.jpg

 

Certification

1.We always feel that all success of our company is directly related to the quality of the products we offer. They meet the highest quality requirements as stipulated in ISO9001:2008, GB/T19001-2008,CE Certification and New Hi-tech Enterprises Certification and our stringent quality control system.

 


Service

Give your advice for low cost with high quality

1. Let’s be honest with each other and make clear the situation of each customer first,then we can give best advice, because we’re over 20 years experience in gearbox reducer.

2. I will give the details to each customer for reference, including the dimension,performance, quality and price level. 

3. We can compare the products one by one, then confirm the reasonable products with best price.


FAQ

1. How to choose a reducer which meets our requirement?

A: You can refer to our catalogue to choose the reducer or we can help to choose when you provide the technical information of required output torque, output speed and motor parameter etc. 

2. What information shall we give before placing a purchase order?

A: Type of the reducer, ratio, input and output type, input flange, mounting position, and motor information etc. 

3. Do you sell motors?

A: We have stable motor suppliers who have been coperating with us for a

long-time. We can provide motors with high qualit. 

4. Are you a manufactuer or trading company?

A: We are a manufactuer,with more than 20 year' experience.

Hot Tags: gearbox rotary reducer, China, suppliers, manufacturers, factory, price, quotation, in stock, made in China
Related Products
  • Contact Us
    Jiangyin Deling Gearbox Co.,Ltd
    Add:No.19 Yingbin Road Qiaoqi Industrial Park Jiangyin City, Jiangsu, China
    Tel:+86-0510-86573908-814
    Mob:+8613915307777
    E-mail:mck@dlclx.cn
  • Categories
  • Copyright © Jiangyin Deling Gearbox Co.,Ltd. All Rights Reserved.