Rotary rig speed reducer introduction
Small size, light weight, torque, efficiency and high starting transmission efficiency, low noise characteristics.
The output shaft can withstand greater radial force. It can be widely used in construction, operating machinery, lorry cranes, railway locomotives, ships, oil drilling, mining, light industry and other mechanical drive mechanism.
1.The three stage planetary size is 60, the A type is installed with the eccentricity of 2.5, and the transmission ratio is 140.
If you have special requirements, please explain when you order.
2. Structure design of rotary reducer
3. Lubricating oil plus and release
The inlet port of the reducer is provided with an air vent and a gas inlet. The large output shaft support bearing adopts a long acting grease without replacement, and the oil level can be inspected through the observation hole.
The location of each oil discharge port is shown below.
4. Eccentricity adjustment
In order to accurately adjust the clearance between the output shaft gear and the gear ring, the eccentricity adjustment between the output gear shaft and the fixed flange can be adjusted when the output shaft is assembled.
5. Eccentric gear shaft
The output gear shaft adopts the spline shaft insert structure or the integral forging structure, and the gear tooth surface hardness HRC57 - 62 (also can be surface hardening on the tooth surface according to the customer's request hardness).
The gear displacement coefficient +0.5 is used to repair the top of the tooth.
6. Performance parameters and dimensions
1) Each minimum value is for reference only in the design range. For specific selection, it is necessary to specify the size.
2) Output pinion gear number, modulus, given at the time of ordering.
3) The flange bolts are graded 10.9.
4) The dimensions D1, D2 are determined by the pinion structure, and the smaller dimensions need to be explained first.
5) For special installation, higher torque and non-standard speed performance requirements, please contact us.
Another: For the following two types of installation requirements, please request the installation size as an order drawing
Nominal transmission ratio
T 2 (N.m): Output pinion load torque
T 2k—Modified load torque
K - Coefficients corresponding to the utilization level and load status of the table organization
The rated torque of the gearbox selected must satisfy the following formula:
T 2k=T 2×K<Tnom (see parameter table)
In order to ensure the normal operation of the slewing mechanism, the mounting center hole of the steel structure must be concentric, and the flange mounting surface must be perpendicular to it. The relative position between the mounting hole of the steel structure and the mounting surface of the flange is not allowed to change excessively under the influence of environmental influences and external forces. The recommended tolerances are as follows.
A: When the workpiece rotates around the reference centerline, the amount of axial runout in any measurement plane must not exceed the value
B: The centerline of each machining axis hole must be located in a cylinder whose deviation from the centerline of the reference plane is this value.
Oil selection and replacement
The correct choice of oil and reasonable maintenance can extend the service life of the reducer.
New reducer or replacement repaired reducer. Use oil for the first time after 200 hours. Replace oil every 1000 hours. Change oil at least once a year.
Add it once a week or 50 hours after work
(3) Recommended Lubricant:
This product can be widely used in the field of lifting machinery，including bridge crane, gantry crane, tower crane, mobile crane, gantry crane, elevator, cable crane, mast crane and mechanical parking equipment.
All exported gearboxes covered with Anti rust oil and plastic film, then packed in wood box with Fumigation.
1. all products sold in our factory are guaranteed for 12 months (except for human factors or irresistible natural phenomena).
2. after consultation, customers can return products with quality problems to the company within seven working days.
3. users can consult technical questions through the after sale telephone, and get a clear solution.
4. in case of performance failure in normal use, the company undertakes the above warranty. In addition, if the State applies laws and regulations, otherwise, the company will comply with relevant laws and regulations.
1. Do you accept Custom orders?
A:Yes, we do.
We can produce it completely according to your drawings.
2. Can I get a sample before mass production?
A: It is no problem to require samples to check the quality.
3. What is your terms of payment?
A: We accept TT, Western Union, Moneygram and Escrow. If you have any request, pls feel free to tell us.